Where can I obtain the user manual for Genius?

How long is the warranty on Genius?

What do the indicator symbols mean on Genius?

NOCO Genius chargers are equipped with LED indicators to indicate standby, charging modes, charge levels and for advanced diagnostics.

How much does Genius weigh?

What is the charging current of Genius?

What is the power consumption of Genius?

Which Genius charger is best for my battery?

Selecting the appropriate charger for your battery will depend on its Amp-Hour (Ah) capacity size. This is usually listed on the battery label at the 20-hour rate, example: “100 AH @ 20HR”. Check your battery for its rated Amp-hour capacity.

Check out the next question What are the charging times for Genius? to learn more.

What are the charging times for Genius?

These are proximate charging times for a battery at 50% depth of discharge.

*Charging times for GENIUS2D, GENIUS2X2, and GENIUS2X4 will be similar to GENIUS2.

What battery voltages is Genius compatible with?

What is the IP rating of Genius?

Can Genius charge a Lead-Carbon battery?

Genius can be used to charge Lead-Carbon batteries by using 12V Mode.

What type of fuse does Genius chargers use?

The fuse is a Mini® Blade fuse which can be purchased at hardware or automotive stores.

How do I change modes on Genius?

When plugged into AC power NOCO Genius will start out in Standby Mode. Press the Mode Button to switch between modes.

What is Repair Mode on Genius?

Repair Mode is an advanced battery recovery mode found on GENIUS5 and GENIUS10 for repairing and storing, old, idle, damaged, stratified or sulfated batteries. Not all batteries can be recovered. Batteries tend to become damaged if kept at a low charge and/or never given the opportunity to receive a full charge. The most common battery problems are battery sulfation and stratification. Both battery sulfation and stratification will artificially raise the open circuit voltage of the battery, causing the battery to appear fully charged, while providing low capacity. Use 12V Repair in attempt to reverse these problems. For optimal results, take the 12-volt battery through a full charge cycle, bringing the battery to full charge, before using this mode. 12V Repair can take up to four (4) hours to complete the recovery process and will return to Standby when completed.

Using Repair Mode on Genius5

Using Repair Mode on Genius10

CAUTION: USE THIS MODE WITH CARE. THIS MODE IS FOR 12-VOLT LEAD-ACID BATTERIES ONLY. THIS MODE USES A HIGH CHARGING VOLTAGE AND MAY CAUSE SOME WATER LOSS IN WET (FLOODED) CELL BATTERIES. BE ADVISED, SOME BATTERIES AND ELECTRONICS MAY BE SENSITIVE TO HIGH CHARGING VOLTAGES. TO MINIMIZE RISKS TO ELECTRONICS, DISCONNECT THE BATTERY BEFORE USING THIS MODE.

What is Supply Mode on GENIUS10?

Supply Mode, found on GENIUS10, converts the charger to a constant current, constant voltage DC power supply. It can be used for powering any 12VDC device, like a tire inflator, oil changer and more. As a power supply, it can also be used to retain a vehicle’s on-board computer settings during battery repair or replacement. 13.6V Supply provides 13.6-volts at 10A with overload protection at 12A (Max).

Using Supply Mode on Genius10

CAUTION: USE THIS MODE WITH EXTREME CARE. SUPPLY MODE DISABLES SAFETY FEATURES AND LIVE POWER IS PRESENT AT THE CONNECTORS. DO NOT TOUCH CONNECTIONS TOGETHER. RISK OF SPARKS, FIRE, EXPLOSION, PROPERTY DAMAGE, INJURY, AND DEATH.

How do I use Force Mode on Genius?

NOCO Genius is able to detect and charge dead batteries as low as 1-volt. For extremely dead batteries lower than 1-volt, manually turn on Force Mode to detect and charge batteries all the way down to zero volts. Follow the links below to learn how to use Force Mode on Genius.

Genius isn’t detecting the battery, how do I force charging to start?

NOCO Genius is able to detect and charge dead batteries as low as 1-volt. For extremely dead batteries lower than 1-volt, manually turn on Force Mode to detect and charge batteries all the way down to zero volts.

See also How do I use Force Mode on Genius?

What does it mean when Genius is flashing a charge LED and Standby Mode?

If a charge LED and Standby mode are flashing this means Genius is in Force Mode. After 5 minutes, the charger will return to the normal charge mode operating and low voltage detection will be reactivated.

When in Force Mode all safety features will be disabled.

See also How do I use Force Mode on Genius?

My Genius charge is stuck in Standby Mode.

If the Standby LED is illuminated it means that Genius is in Standby Mode and it is not recognizing that it is connected to a battery. This can happen when there is no battery connected to the charger, if the voltage on the battery is lower than the recognition threshold (1V), if the connection to the battery is faulty, or if the inline fuse is faulty or loose in the fuse housing.

See also How do I use Force Mode on Genius?

Genius is getting hot, is that normal?

Depending on the battery condition and size, Genius can get up to 85°C or 185°F while it is charging the battery. This would be considered normal operating conditions.

Can I run a load on the battery while charging?

It is not recommended to run a load on the batteries while they are being charged.

The green LED went straight to flashing instead of going solid, is that normal?

It is normal functionality for Genius to go sometimes go straight to Maintenance Mode after normal charging is complete.

Click here to learn more about the Charge LEDs on Genius.

The green LED is flashing, is charging done?

When Genius has a slowly pulsating green LED it means the charger is in Maintenance Mode. After the battery is fully charged, the charger will continue to provide ongoing maintenance and optimization until disconnected.

Click here to learn more about the Charge LEDs on Genius.

What does the Overvoltage Error LED mean?

If the Overvoltage LED is illuminated, this means the battery’s voltage is too high for the charge mode that is selected. For example, if you have a 12V battery and have selected a 6V charging mode selected.

What does the Bad Battery Error LED mean?

If the Bad Battery Error LED is illuminated, this means that the battery is not holding a charge, or there may be a short in the battery. We recommend taking the battery into a local battery shop for a thorough evaluation of its health and status.

All the Error LEDs are flashing. What is wrong?

If the Overvoltage, Battery, and Standby LEDs are flashing together, either the charger’s internal temperature is too hot, or the ambient temperature is too cold for operation. If the charger’s internal temperature is too hot, the charger will stop displaying the error and resume function after the charger cools down. If the ambient temperature is too cold, the charger will resume function when the ambient temperature rises.

Does NOCO make a protective case for Genius?

Yes. NOCO makes a universal sized Protective Case for Genius chargers. This case works well with GENIUS1, GENIUS2, GENIUS5 and GENIUS10 chargers.

EVA Protective Case for Genius Smart Battery Chargers

Where can I find the serial number on Genius?

All NOCO Genius Chargers are marked with a unique serial identification number, usually found stamped on the side or edge of the unit. Click the link below to find the serial number location on each model.

Locating the Serial Number on Genius